Страница 1 из 1

Tippmann A5 и все о нем.

СообщениеДобавлено: 12 сен 2007, 13:08
Партизан
Это если я правильно понял (если не правильно поправьте) один из бюджетных способов снизить вероятность расколов в циклоне в процессе "мешания", защет закругления всех острых краев. Смысл мода в придании лопостям крыльчатки и язычка более закругленных форм, т.е. стачиваются кромки на язычке и выступ на внутренних сторонах лопостей.

Something interesting about your cyclone.

--------------------------------------------------------------------------------

Here is something interesting that some of you may or may not have tried regarding your cyclone feeder.

In short, I was having some paint breaking issues in my cyclone awhile back. I had attributed this to using some paint that was too brittle, and indeed the paint was very brittle.

However, I had my first game of the season a week ago, and had to use field paint only. It was good paint, and it would survive the drop test for five drops. But! I was still breaking a lot of paint at this game.

Now, to the point of my post: After de-burring the following places where paint comes in contact with the marker receiver half, I was still having paint breaks at an alarming rate!

The first two photos reference something that I have seen posted before...
Изображение
Изображение
Now for the most important photo of the day!!
Изображение
I noticed that each of the cyclone sprockets/paddles had sharp edges on the "leading" edge of the sprockets. All you need to do is round these edges over and "blend" them into a more natural curve with the rest of the sprocket.

Also, round over the tops of the sprockets, as paint rides around on top of the sprocket before it can fall into place to be fed into the marker.

Any sharp edge will knock a whole in the paintball before it enters the chamber! A recipe for disaster!

So far, I have not broken anymore paint after having smoothed off the sprockets!

СообщениеДобавлено: 12 сен 2007, 14:55
Партизан
Вот еще один вариант доводки до ума циклона. На практике должно уменьшиться усилие необходимое для перевода трещетки из состояния покоя в режим зацепления за зуб шестеренки миксера с последующим поворотом (во загнул :lol: ).

http://www.a5og.net/5-mods-upgrades/235 ... t-mod.html

Вчера сделал то же самое со своим циклоном. На первый взгляд: значительно снизилось усилие, прилогаемое для нажатие на кнопку циклона. По-сути стало похоже на "шариковую ручку", может быть чуть жоще. Еще откусил один виток от пружины (которая возвращает курок в исходное положение. пружина красноватого цвета) в рукоятке. На переправе Граф проведет испытания. Если верить отзывам, фпс увеличивается с 16 до 23 :twisted:
TRIPPLE POST!!!
Shoot me....

HOLY @#$)@$... I just did it this night and went from 16 to 23 bps... NO THAT WAS NOT A TYPO

THATS CRAZYYYYYYYYY!!! i dont even have a Qev...
I had some small problems but nothing huge...
After i tested that i started doing the X7 drills but broke my only 1/16 drill bit... Im going to do it at school on a drill press monday...
Ill go into more details into that later...

I used white lithium grease and i also bent the rod that keeps pressure on the rachet... (very very little... i just felt like it was putting way 2 much pressure on the rachet)

All i can say is... wow...

СообщениеДобавлено: 13 сен 2007, 14:53
Партизан
Изображение
Изображение

Re:

СообщениеДобавлено: 19 фев 2009, 13:08
paintballno.ru
Партизан писал(а):Изображение
Изображение

круто)